Remove the negative battery cable from the negative battery terminal. The negative battery cable or grounding cable connects the negative lead post of the Ford battery with the frame or chassis of the vehicle.
Use the 10 mm wrench to loosen the bolt that holds the cable clamp onto the lead post. Connect the stereo wiring in the Ford Explorer to a wiring harness adapter.
The wiring harness adapter will be labeled to illustrate where the proper connections are to be made some wiring harness adapters will list the wiring diagrams in their operation manual. Slide the installation sleeve from the Ford aftermarket stereo installation kit into the empty stereo mounting dock. The sleeve provides a uniform platform for installation of varied aftermarket stereo decks. Connect the wiring harness adapter leads and antenna cable from the stereo mounting dock of the Ford Explorer to the back of the aftermarket stereo.
The wiring harness adapter leads and antenna cable will plug into the corresponding outlets on the rear panel of the stereo. Place the grounding cable clamp over the negative lead post of the Ford battery. Tighten the clamp to the lead post with the 10 mm wrench. Lift the hood of the Rodeo and disconnect the grounding cable from the negative terminal of the battery. Use a 10 mm wrench to loosen the bolt holding the cable clamp to the lead. Move the cable from the negative lead and rest it away from the battery until the new radio is installed.
Slide the ashtray from its slot in the dashboard. Remove the metal ashtray bracket from the opening. Remove the screw in the back of the empty compartment with the Phillips-head screwdriver.
Pry the dash panel that surrounds the stereo away from the dashboard with a trim-panel removal tool. Grab the panel once it is free from the dash, and pull it away from the dashboard. Pull the wiring connection to the cigarette lighter away from the back of the panel. Remove the two screws on either side of the stereo mounting bracket with the screwdriver.
Slide the stereo from its dock and unplug the stereo wiring and antenna cable from the rear panel of the radio. Slide the factory stereo from the bracket.
Place the faceplate adapter into the bracket and replace the screws on the side. Slide the aftermarket stereo into the adapter. Connect the stereo wiring to the wiring harness adapter. Plug the wiring harness adapter leads into the back of the new stereo. Plug the antenna cable into the FM antenna outlet on the right side of the new radio's rear panel.
Slide the stereo mounting bracket, with new radio installed, into the stereo mounting dock. Replace the two screws on either side of the stereo assembly. Plug the wiring for the cigarette lighter into the back of the dash panel that covers the stereo. Place the panel into position on the dashboard and press firmly around the perimeter of the panel, snapping the panel into place.
Replace the screw in the back of the ashtray compartment. Place the ashtray bracket into the opening and the ashtray into its slot. Replace the negative battery cable over the negative lead post of the Rodeo's battery. Tighten the bolt on the cable's clamp to secure the cable onto the negative battery terminal.
Close the hood of the Isuzu Rodeo. Park your Cavalier with the front wheels pointing straight ahead. Turn off all lamps accessories and turn the ignition switch off. If your car is equipped with OnStar, open the driver's door to disable the retained accessory power. Remove the bolt for the negative battery cable and route the cable aside. Wait at least one minute before proceeding to allow the airbag system to deactivate. Remove the screw in the defroster grille vent on the dashboard pad and then pry the grille from the dashboard pad.
Use the trim tool to disengage the outer trim covers from the dashboard pad, then pull the covers rearward to disengage the retainer tabs from dashboard pad.
Open the glovebox and remove the screws across the top of the glovebox opening, then remove the dashboard pad. Remove three screws across the top of the dashboard fascia panel, then pull the fascia panel toward you to disengage the retainer tabs. Reach behind the fascia panel and disconnect the electrical connectors for the headlamp dimmer switch and the cigar lighter. Remove the fascia panel. Remove three screws from the audio unit mount, then slide the audio unit toward you.
Reach behind the unit and disconnect the electrical connectors and the antenna coaxial cable, then remove the audio unit. Connect the coaxial cable and the electrical connectors to the back of the audio unit and then slide it into the dash. Install the mount screws and tighten them to 20 inch-pounds. Connect the electrical connectors to the back of the dashboard fascia panel. Align the dashboard fascia panel and press it into place to engage the retainer tabs.
Install the screws and tighten them to 20 inch-pounds. Install the dashboard pad. When it is a wiring harness, you can use another harness for your new unit and simply connect them all in one shot.
Connect each wire for each speaker each should have a positive and negative one by one. Connect the ground to a metal connection probably a screw on the back of your new unit. Connect the power wires to your new CD player.
They are both red, and your manual should indicate where they are connected to the back of your CD player. Plug your car battery back in and test your CD player.
When it works, slide it into the slot and screw it in securely. This article was written by a professional writer, copy edited and fact checked through a multi-point auditing system, in efforts to ensure our readers only receive the best information. To submit your questions or ideas, or to simply learn more, see our about us page: link below.
Step 1 Buy a CD player that is compatible with the already existing slot in your car. Step 2 Read the owner's manual. Step 3 Collect your tools. Step 5 Remove the dashboard and your old unit. Step 6 Check to see if the wires go into the old unit one by one or through a wiring harness. Step 7 Connect each wire for each speaker each should have a positive and negative one by one. Step 8 Connect the power wires to your new CD player.
Tips If looks and sound are not priorities, if all you need is something to sing along to Journey songs with, just put a portable boom box in your back seat or get a tape adapter for your portable CD player.
0コメント